单缸液压圆锥破碎机具有先进的结构设计、强大的破碎能力和低廉的生产运行成本等特点。液压圆锥破通过单个液压缸升降动锥,实现了排矿口调整、清腔、过铁和过载保护等多种功能;配置电子智能排矿口控制系统,实现了更多生产过程控制和作业优化功能。单缸液压圆锥式破碎机可广泛应用于各黑色、有色、非金属矿山及砂石料等工业领域。
单缸液压圆锥破碎机工作原理
电机带动破碎机的小齿轮,小齿轮带动大齿轮,大齿轮组件(大齿轮、大齿轮架、偏心钢套)带动偏心套组件(偏心缸套、偏心铜套)和主轴组件(主轴、内锥、内锥衬板)以理论垂直线为中心,在铜衬套内公转,主轴组件在偏心铜套内以主轴的中心线可以实现自转。空机运行的时候,偏心套组件“抱着”主轴组件和随大齿轮一同公转,当物料加入到破碎腔后,主轴总成(主轴、内锥)在物料的阻力下在偏心铜套内缓慢的自转。内锥的运行轨迹看起来是在破碎腔内来回摆动,同时缓慢的旋转。物料被摆动的内锥挤压破碎。支撑套与架体连接处靠液压缸压紧,当破碎机内落入金属块等不可破碎物体时,单缸的动锥由底部液压活塞托起,起到排放口调整和过铁保护、反复起落排除堵矿的作用。
出料口大小的调整:底部液压缸的第一个功能在于调节主轴的上下位置,从而调节动锥和外锥衬板之间的间距。这个间距变小了,破碎机的出料粒度就小;这个间距变大了,破碎机的出料粒度就大。同时,选用不同的破碎腔型,选用不同的偏心套也能够改变物料的出料大小。
单缸液压圆锥破碎机用途
适用于冶金、建筑、筑路、化学及硅酸盐行业中原料的破碎,可以破碎中等和中等硬度以上的各种矿石和岩石。液压圆锥破破碎比大、效率高、能耗低,立博·产品粒度均匀,适合中碎和细碎各种矿石,岩石。
单缸液压圆锥破碎机性能特点
1、高效率:该液压圆锥破碎机主轴上下两端均有支撑,能承受更大的破碎力和更大的冲程,加上与层压原理相适应的特殊破碎腔形,使该机具有更高的破碎效率。
2、生产能力大:该液压圆锥破碎机将破碎冲程、破碎速度以及破碎腔形状的完善组合设计,使该机在动锥大端直径相同的情况下,比老式弹簧圆锥破的产量高 35%~60%。
3、高质量的石子:该液压圆锥破碎机采用特有的破碎腔形以及层压破碎原理,产生颗粒间的破碎作用,从而使成品中立方体所占的比例明显增高,针片状石子减少,粒级更为均匀。
4、多种腔形的中细破碎,仅仅更换定锥既可实现。
5、双保险控制的液压与润滑系统,可确保该机的过载保护与良好的轴承润滑。
6、易于维修:圆锥破碎机结构简单而紧凑,性能稳定,不易故障。维修方便快捷。
单缸液压圆锥破碎机特点
1、破碎比大、生产效率高。
2、层压破碎、成品粒级更均匀。
3、易损件消耗少、运行成本低。
4、粗细破碎,仅仅更换定锥既可实现。
5、先进的液压技术,实现了过载保护和液压调整排料口,简化了破碎机结构,减轻了重量。
6、稀油润滑、可靠先进、提高使用寿命。
7、维修简便、操作使用方便。
Cylinder Hydraulic Cone Crusher is a new high-efficiency cone crusher independently researched, developed and designed by HENGJI through summarizing over twenty years of experience and widely absorbing advanced American and German technologies about cone crushers. This cone crusher integrates mechanical, hydraulic, electrical, automation and intelligent control technologies, and possesses advanced cone crusher technologies in the world.
Input Size: 0-370mm
Capacity: 45-2000TPH
Material: Granite, diabase, basalt, pebble, limestone, dolomite, metallic ores and non-metallic ores, etc.
Working Principle
When a CH Single Cylinder Hydraulic Cone Crusher works, driven by the motor, the transmission shaft rotates under the action of belt pulley and triangular belt. Next, the transmission shaft drives the eccentric sleeve to make it rotate around the axis. Meanwhile, the eccentric sleeve forces the movable cone to do pendular movement. This movement makes the movable cone and fixed cone sometimes close to, sometimes far away from the rolling wall. Materials are continuously shocked, squeezed and crushed in the crushing cavity between the crushing wall and the rolling wall. Finally, materials are discharged out of the machine when their fineness reaches the discharging standard.
Product Parameters
型号Model | 腔型Cavities |
给料口最大尺寸(mm) Maximum feeding size(mm) |
紧边排料口尺寸(mm) Minimum discharging size (mm) |
处理能力Capacities (t/h) |
标配装机功率~最大装机功率 Nominal ~Maximum installed power (kw) |
重量Weight (t) |
CS430 | EC(超粗)Extra Coarse | 360 | 25-54 | 125-415 | 132~160 | 12 |
C(粗) Coarse | 300 | 22-48 | 110-340 | |||
MC(中粗)Medium Coarse | 235 | 22-48 | 95-260 | |||
CS440 | EC(超粗)Extra Coarse | 450 | 35-54 | 265-640 |
220~280 | 19.3 |
C(粗)Coarse | 400 | 29-51 | 225-490 | |||
MC(中粗)Medium Coarse | 300 | 25-51 | 195-445 | |||
CS660 | EC(超粗)Extra Coarse | 450 | 41-70 | 350-1050 | 315~355 | 35.7 |
C(粗) Coarse | 400 | 38-70 | 320-930 | |||
CH430 | EC(超粗)Extra Coarse | 185 | 13-38 | 70-220 | 132~160 | 9.2 |
C(粗) Coarse | 145 | 13-38 | 65-150 | |||
MC(中粗)Medium Coarse | 115 | 10-32 | 55-190 | |||
F(细)Fine | 90 | 8-32 | 60-180 | |||
MF(中细)Medium Fine | 75 | 8-25 | 50-135 | |||
EF(超细)Extra Fine | 50 | 10-25 | 55-120 | |||
CH440 | EC(超粗)Extra Coarse | 215 | 16-44 | 115-415 | 220~250 | 14.3 |
C(粗)Coarse | 175 | 13-38 | 100-405 | |||
MC(中粗)Medium Coarse | 140 | 13-38 | 95-350 | |||
F(细)Fine | 110 | 13-38 | 115-300 | |||
MF(中细)Medium Fine | 85 | 8-51 | 90-510 | |||
EF(超细)Extra Fine | 70 | 10-51 | 95-360 | |||
CH660 | EC(超粗)Extra Coarse | 275 | 16-51 | 175-655 | 315~355 | 24.2 |
C(粗) Coarse | 215 | 16-44 | 170-645 | |||
MC(中粗)Medium Coarse | 175 | 16-44 | 160-500 | |||
F(细)Fine | 135 | 16-70 | 195-1330 | |||
MF(中细)Medium Fine | 195 | 13-70 | 190-1865 | |||
EF(超细)Extra Fine | 85 | 13-70 | 195-1890 |
Note:
1.The bulk specific weight is calculated by 1.6t/m³. When the width of the feeding port is above 600mm, it is a large-scale machine while when the width ranges from 300 to 600mm, it is a medium-sized machine.
2.Product pictures and parameters about models, data, performances and specifications on this website are for reference only. There is a chance that HENGJI may make changes on above-mentioned information. For specific messages, please refer to the real objects and user manuals. Without special instructions, HENGJI keeps the right to explain all data involved in this website.